Posts Tagged a400

Tenor A400 sample configuration (1)

Tenor A400 sample configuration (1)

Unit
----
Unit: 1
IP Address = 192.168.0.96
External IP Address = 0.0.0.0
Name = a400
Voip = Sip(1)

Online = 1
Relay ResetTime = 240
Relay Reset Number = 2

TcpKeepAlive = Disabled(0)

System
------
Country Value = 15
Country Code = 852
Area Code = 732
Minimum DN = 7
Maximum DN = 7
International Prefix:
1: 011
Long Distance Prefix = 1
Carrier Selection Prefix:
Intercom Used = yes(1)
Intercom Prefix = None
Centrex Prefix = None
Pstn Route Prefix = 0
Ip Route Prefix = 7
Multipath Prefix = 9
Private DN Used = yes(1)
Private DN Length = 4
Interdigit Timeout = 4 sec.

Contact =
Location =
IP Address : of Snmp Trap Server 1 = 0.0.0.0
IP Address : of Snmp Trap Server 2 = 0.0.0.0
IP Address : of Snmp Trap Server 3 = 0.0.0.0

IP Address : Port # of Syslog Server 1 = 0.0.0.0 : 514
IP Address : Port # of Syslog Server 2 = 0.0.0.0 : 514
IP Address : Port # of Syslog Server 3 = 0.0.0.0 : 514
Syslog Facility = 16

IP Address : Port # of Cdr Server 1 = 0.0.0.0 : 0
IP Address : Port # of Cdr Server 2 = 0.0.0.0 : 0
Cdr Password:
Cdr Format: 0

Ring Frequency = 20 Hz(0)
PSTN Ring Sensitivity = Normal(0)

Primary Time Server:    IP Address = 210.0.235.14
Secondary Time Server:  IP Address = 0.0.0.0
UTC Offset:             Unknown

Disc Tone Frequency: 480 Hz (min) : 620 Hz (max)
Disconnect On/Off Time: 250 mSec(on) : 250 mSec(off)

Call Indication Tone = None(0)

Dialplan
--------
User Programmable DP = No
Dialplan table:
index:Pattern    DpType         min     max     nprefix

System LAN
----------
Subnet Mask = 255.255.255.0
Default Gateway = 192.168.0.254

PSTN Trunk Group
----------------
PSTN Trunk Group: 1
Name = PstnPassThrough1
Pass Through = yes(1)
PT Trunk ID = 0
Provide Call Progress Tone = no(0)
Busyout = no(0)
Hunt Algorithm = ascending(0)
Modem Bypass = no(0)
Direction = both(2)
DN Used = public
End Of Dial = yes(1)
End Of Dial Digit = #
Add End of Dial Digit = no(0)
Ivr Type = None
External Routing Request = no(0)
Auto Switch Enable = no(0)
Forced IP Routing # = none
Trunk ID(Account Code) = none
Trunk ID Delivery =  none
2 Stage Dial = No
IP Extension = no(0)
Maximum LAM Calls Allowed = 4
LAM: Index Pattern Replacement NumberType
Cas Signaling Type = loop start(1)
Cas Orientation = user(0)
Dial Tone Detect = yes(1)
Dial Delay Timeout = 1000
Answer Delay Timeout = 0
Flash-Hook Signaling = no(0)
Supervision = none(0)
Caller Id Detection = no(0)
dtmf-ontime = 100
dtmf-offtime = 100
Channel:

PBX Trunk Group
---------------
PBX Trunk Group: 1
Name = pbxtg1
Pass Through = yes(1)
PT Trunk ID = 0
Provide Call Progress Tone = yes(1)
Multipath = yes(1)
Hunt Algorithm = ascending(0)
Modem Bypass = no(0)
Direction = both(2)
DN Used = public
End Of Dial = yes(1)
End Of Dial Digit = #
Add End of Dial Digit = no(0)
Ivr Type = None
Partial TG = no(0)
External Routing Request = no(0)
Auto Switch Enable = no(0)
Forced IP Routing # = none
Trunk ID(Account Code) = none
Trunk ID Delivery =  none
2 Stage Dial = No
IP Extension = no(0)
Public Number of Digits = 7
Private Number of Digits = 4
Public Hunt Ldn's:
Private Hunt Ldn's:
1: 1001
BDN: Index Bdn
Cas Signaling Type = loop start(1)
Cas Orientation = net(2)
Flash-Hook Signaling = yes(1)
Flash-Hook Min = 200
Flash-Hook Max = 700
Supervision = none(0)
Caller Id Generation = yes(1)
dtmf-ontime = 100
dtmf-offtime = 100
Channel:
unit# 1 line# 1: 1
PBX Trunk Group: 2
Name = pbxtg2
Pass Through = yes(1)
PT Trunk ID = 1
Provide Call Progress Tone = yes(1)
Multipath = yes(1)
Hunt Algorithm = ascending(0)
Modem Bypass = no(0)
Direction = both(2)
DN Used = public
End Of Dial = yes(1)
End Of Dial Digit = #
Add End of Dial Digit = no(0)
Ivr Type = None
Partial TG = no(0)
External Routing Request = no(0)
Auto Switch Enable = no(0)
Forced IP Routing # = none
Trunk ID(Account Code) = none
Trunk ID Delivery =  none
2 Stage Dial = No
IP Extension = no(0)
Public Number of Digits = 7
Private Number of Digits = 4
Public Hunt Ldn's:
Private Hunt Ldn's:
1: 1002
2: 2002
BDN: Index Bdn
Cas Signaling Type = loop start(1)
Cas Orientation = net(2)
Flash-Hook Signaling = yes(1)
Flash-Hook Min = 200
Flash-Hook Max = 700
Supervision = none(0)
Caller Id Generation = yes(1)
dtmf-ontime = 100
dtmf-offtime = 100
Channel:
unit# 1 line# 1: 2
PBX Trunk Group: 5
Name = pbxtg5
Pass Through = yes(1)
PT Trunk ID = 4
Provide Call Progress Tone = yes(1)
Multipath = yes(1)
Hunt Algorithm = ascending(0)
Modem Bypass = no(0)
Direction = both(2)
DN Used = public
End Of Dial = yes(1)
End Of Dial Digit = #
Add End of Dial Digit = no(0)
Ivr Type = None
Partial TG = no(0)
External Routing Request = no(0)
Auto Switch Enable = no(0)
Forced IP Routing # = none
Trunk ID(Account Code) = none
Trunk ID Delivery =  none
2 Stage Dial = No
IP Extension = no(0)
Public Number of Digits = 7
Private Number of Digits = 4
Public Hunt Ldn's:
Private Hunt Ldn's:
BDN: Index Bdn
Cas Signaling Type = loop start(1)
Cas Orientation = net(2)
Flash-Hook Signaling = yes(1)
Flash-Hook Min = 200
Flash-Hook Max = 700
Supervision = none(0)
Caller Id Generation = yes(1)
dtmf-ontime = 100
dtmf-offtime = 100
Channel:

IP     Trunk Group
---------------
Incoming IP call delete digits = 0
Incoming IP call prefix =
Outgoing IP call delete digits = 0
Outgoing IP call prefix =
Prefix Trunk ID = no(0)
Default Trunk = No
External Routing Request = no(0)
Display Information ID = Tenor-Gateway

Line
----
Line: 1
Law = uLaw(0)
Rx Gain = -4dB
Tx Gain = -2dB
Line: 2
Law = uLaw(0)
Rx Gain = 0dB
Tx Gain = 0dB
Guard Time = 0mS
DAA Start Up = Enabled

Bandwidth Management
--------------------
Time of Day Maximum Bandwidth:
Day  = 0(Sunday)
Hour = 00       *        *        *        *        *        *
Hour = 06       *        *        *        *        *        *
Hour = 12       *        *        *        *        *        *
Hour = 18       *        *        *        *        *        *
Day  = 1(Monday)
Hour = 00       *        *        *        *        *        *
Hour = 06       *        *        *        *        *        *
Hour = 12       *        *        *        *        *        *
Hour = 18       *        *        *        *        *        *
Day  = 2(Tuesday)
Hour = 00       *        *        *        *        *        *
Hour = 06       *        *        *        *        *        *
Hour = 12       *        *        *        *        *        *
Hour = 18       *        *        *        *        *        *
Day  = 3(Wednesday)
Hour = 00       *        *        *        *        *        *
Hour = 06       *        *        *        *        *        *
Hour = 12       *        *        *        *        *        *
Hour = 18       *        *        *        *        *        *
Day  = 4(Thursday)
Hour = 00       *        *        *        *        *        *
Hour = 06       *        *        *        *        *        *
Hour = 12       *        *        *        *        *        *
Hour = 18       *        *        *        *        *        *
Day  = 5(Friday)
Hour = 00       *        *        *        *        *        *
Hour = 06       *        *        *        *        *        *
Hour = 12       *        *        *        *        *        *
Hour = 18       *        *        *        *        *        *
Day  = 6(Saturday)
Hour = 00       *        *        *        *        *        *
Hour = 06       *        *        *        *        *        *
Hour = 12       *        *        *        *        *        *
Hour = 18       *        *        *        *        *        *

Gatekeeper Administration
-------------------------

Endpoint Authorization Type = 0 (None)

Allowed Endpoints
IP                      Mask
No Allowed Endpoints Configured

Barred Endpoints
IP                      Mask
No Barred Endpoints Configured

Gatekeeper System
-----------------
Zone Name =
Border Element IP Address(prim) = 0.0.0.0
Border Element IP Address(sec) = 0.0.0.0
Discovery IP Address = 0.0.0.0
Gatekeeper Password =
LRQ returns all candidates(0)
Maximum LRQ Hops = 0
WAN Call Limit = 0 (disabled)
LCF/LRJ V3plus = 1
Gatekeeper Option Flags:
Use IP Header Address = no(0)
Ridgeway ARQ = no(0)

Border Element
-----------------
Static Routing
No Static Routes configured

DSP
---
Voice Coding algorithm = 8
Voice Information Field size = 1280 bits
Silence Suppression = Enable(1)
Minimum Jitter buffer = 60 msec
Maximum Jitter buffer = 150 msec
Receive Gain (PCM -> IP) = -2 dB
Transmit Gain (IP -> PCM) = -4 dB
Digit Relay = 0
Fax Relay Type = 0
Fax Maximum Rate = 144
Fax Playout FIFO nominal delay = 600
Fax Coding = 0
Idle Time = 0
Answer Supervision Options = 0

AutoSwitch
----------
Auto Threshold = 50

H323 Gateway
-----------------
Primary GK Address = 0.0.0.0
Primary Auto Discovery = 1
Secondary GK Address = 0.0.0.0
Secondary Auto Discovery = 0
H.323 ID =
Register DN = Register as GW Prefixes(1)
Ignore Bandwidth in ACF = no(0)
Default H245 Tunneling = yes(1)
Round Trip Delay = 0
One Stage Dialing = 0
RRQ Interval = 0
H323 Interop Flags:
H225 GW Protocol = h323(0)
Do BRQ = 0
SlaveSessionId0 = 0
AllowFastStartOnly = No(0)
RRQv3plus= No(0)
ProgressInd Alert= No(0)
StartH245Flag= No(0)
Automatic Ext IP Update= No(0)

Do Lightweight RRQ = no(0)

Radius User
-----------

host p 0.0.0.0
authenticationport p 1812
accountingport p 1813

host s 0.0.0.0
authenticationport s 1812
accountingport s 1813

retry = 3
timeout = 5
accountingtype = 0
billingvendor 0
sharedsecret

IVR
------

Primary File Server:    IP Address = 0.0.0.0
Secondary File Server:  IP Address = 0.0.0.0
timeout:        5

Enabled Languages:      None

Radius Endpoint
---------------

host p 0.0.0.0
authenticationport p 1812
accountingport p 1813

host s 0.0.0.0
authenticationport s 1812
accountingport s 1813

retry = 3
timeout = 5
idtype = 0
passwordtype = 0
sharedsecret

Sip
---------------
Primary Registrar = 0.0.0.0:0000
Primary Registrar User Name= a400
Primary Registrar Pwd= a400
Primary Proxy = 0.0.0.0:0000
Primary Proxy User Name= a400
Primary Proxy Pwd= a400
Secondary Registrar = 0.0.0.0:0000
Secondary Registrar User Name=
Secondary Registrar Pwd=
Secondary Proxy = 0.0.0.0:0000
Secpndary Proxy User Name=
Secondary Proxy Pwd=
User Agent port = 5060
Time to Live = 0

Product Name: Tenor Analog A400 Multipath Switch - 4 ports (Rev. B)
Gatekeeper Status: Mini
GK Calls Allowed: 4
Feature Bit Status: -PS/+RB/-ER
Languages allowed: 1
Serial Number: A002-008663
Ethernet Address: 00-30-E1-00-86-63
IP Address: 192.168.0.96
Subnet Mask: 255.255.255.0
Default Gateway: 192.168.0.254
System Software Version: P5-2-1(LEC) (1678285/0xFF74)
Boot Software Version: P4-1-3 (180592/0xE814)
Database Version: 2.08 09-13-2000 (278376)
VN:F [1.9.18_1163]
Rating: 0.0/5 (0 votes cast)
VN:F [1.9.18_1163]
Rating: 0 (from 0 votes)
Total views: 16,102 views

, ,

7 Comments

Tenor A400 DTMF inband with Asterisk

Tenor A400 DTMF inband with Asterisk

When you are using A400 to access Voicemail provided by Asterisk, you may not be able to submit the “digit” or “key” to it.

If you are facing this case, you can consider to do the following configuration.

1. In Asterisk sip.conf,
Configure
dtmfmode=inband

2. In A400,
Configure
dsp digitrelay 1

digitrelay

digitrelay

Description: Digit Relay. Used to set how the Tenor sends DTMF tones during a VoIP call. Sending DTMF tones in-band (the same path as the voice) over IP is extremely unreliable. It is not uncommon for these tones to be misinterpreted as a different digit than what was entered. Therefore, the Tenor, by default, will regenerate the tones in that, when a Tenor senses that a user has pushed digits during a call, the Tenor will translate the tones to the literal digit, send that information over IP to the destination Tenor. The destination Tenor will convert the digit back to a tone and insert it on to the correct voice path. This provides a high degree of accuracy when sending DTMF tones. However, some devices, such as Microsoft’s NetMeeting, do not support this method and can only send the digits in-band. This command allows you to choose the DTMF method.

Cmd Type: Command.

Prompt Level: config dsp#

Syntax: digitrelay or digit {0 | 1}

Arguments:

0 H.245 regenerate dtmf tones and send out-of-band.

1 Allow DTMF tones to be sent in-band of the voice call.

Default: 0 – out-of-band DTMF.

Availability: All Tenor releases.

Examples:

config dsp# digitrelay 1

Sets the Tenor to send and receive DTMF tones in-band on the voice call.

VN:F [1.9.18_1163]
Rating: 0.0/5 (0 votes cast)
VN:F [1.9.18_1163]
Rating: 0 (from 0 votes)
Total views: 8,171 views

, , ,

No Comments